BURN RESTORE

Acid Burn Repair System for Glazed Brick

Description and Use:
Burn Restore is a special product that creates a residual non hazardous breathable barrier on the surface that is capable of long term repair of the damage. This product is not corrosive and is water based and can be removed with a pressure washer or by rinsing with a garden hose and scrubbing immediately after application. After it cures rain water will generally not affect it and it will be bonded to the surface permanently. Burn Restore has no effect on the unburned masonry surfaces next to the burned areas so it very easy to apply. This product was designed to be used on glazed brick with smooth faces that burn and get white readily from hydrofluoric acid products. It may or may not work on the bleached burning that comes on porous masonry surfaces from using hydrofluoric acids too strong. This product has no effect on glass and will not cure acid burn on that surface. This system has proven effective at hiding burn, where it has been used for almost two decades, and shows no sign of failing in long term application.

Advantages:
* Non corrosive.
* Has no effect on unburned masonry.

Limitations:
*May not work on bleached burning on porous masonry stemming from strong HF acids too strong.

Technical Data:
Appearance & Odor: Clear liquid, mild odor.
Physical State: Liquid
pH: 9.5
Vapor Pressure (mmHg): N/A
Vapor Density (air= 1) : >1
Boiling Point: 212° F
Evaporation Rate: <1
Freezing Point: 32° F
Specific Gravity (WATER =1) : 1.004
Solubility in Water: Complete

Pre-Testing:
Always test prior to beginning full scale operations. Confirm effectiveness on each type of surface designated to be treated before evaluating final appearance and results.

Application Instructions:
Clean, rinse and let dry, the substrate prior to applying the coating.  Apply straight with a brush or paint roller. Roll on a generous even coating all over the affected areas allowing plenty of overlap onto unaffected areas. The surface will immediately return to its’ original appearance if the product is going to work. There will be a very slight immediate darkening of the unaffected areas but that should be basically invisible once the product dries which should in normal conditions take less than ten minutes. Occasionally on certain surfaces that are rougher or very non- absorbent a second application may be required to finish the job. You should not clean over or rinse the area once it has been repaired. Do not apply Burn Restore in a rain storm or if a hard rain is going to occur in less than an 4 hours.

Coverage Rates:
Coverage rates will vary from 100 - 250 sq. ft. /gal depending on the surface porosity, texture and severity of staining.

Safety Information:

*Precautionary Measures: Wear goggles and rubber gloves when handling this product. Keep off of skin and clothing. If material comes in contact with clothing, wash before reuse. Contains Ethylene Diamine tetracetic acid. Do not get in eyes, on skin or clothing. Keep container closed when not in use. Applicators should wear gloves and goggles to avoid splash to bare skin or eyes. Dispose of empty containers according to federal, state and local requirements. Do not dilute Burn Restore. Do not use for any other applications other than specified. Do not remove label. Read Material Safety Data Sheet for additional safety and health hazard information prior to use.

*First Aid -+
 Instructions in Case of Contact or Exposure Skin & Eye Contact:
Eyes: Flush with water for 15 minutes, if irritation persists consult physician.
Skin: Wash off with soap & water. If irritation develops, call physician.
Inhalation: Drink large amounts of water. Seek medical attention.
Ingestion: N/A.

Spill or Leak Procedures:
For large spill: dike and contain for intended purpose.
Small Spill: absorb with oil - dry and dispose of properly.

Waste Disposal Method:
Check state, local or federal regulations for your area. Steps to be taken if material is released or spilled: Large spill; dike and contain for intended use. Small spill; absorb on oil dry and place in approved container for disposal.

Container Handling/Storage:
Store in a cool dry place. Keep container tightly closed when not in use. Wash thoroughly after handling. Empty containers retain residue and must be handled as if full.

Notice:
This product has been classified in accordance with the hazard criteria of the CFR.

Disclaimer:
The information herein is given in good faith, but no warranty, either expressed or implied is made. Final determination of the suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein we cannot be sure or guarantee these are the only hazards which exist.

Customer Service:
Factory personnel are available for assistance at 800-313-8505 and will send you additional information on products as necessary.