ACRYLIC REMOVAL, Coatings
Stripsol will remove multiple layers of acrylics, latexes, acrylic latexes, alkyds, certain enamels, oil based stains, polyurethanes and other resin coatings. This stripper is not flammable, has very little odor, does not burn the skin and does little to no damage on most substrates to which it would be applied. Always test the product in an inconspicuous area before starting the job.
^TOP

ANODIZED ALUMINUM, Cleaning
SafeRestorewill safely clean anodized aluminum and will not etch glass. Its best functions are to remove existing oxidation and provide surface resistance to new oxidation. This cleaner is capable of removing pollution and many sealers as well, but will not remove the pits that occur from neglect.
^ TOP

ANODIZED ALUMINUM, Restoration
After cleaning with SafeRestore, follow up with an application of Anodized Restoration Treatment (A.R.T.) to restore the surface to a "like new" appearance. Product is applied straight to a clean, dry surface and allowed to air dry.
^ TOP

ALUMINUM SIDING
Cleansol works well when cleaning aluminum siding. Dilute from 4:1 to 20:1 for brushless results, then rinse with a pressure washer.
^ TOP

ALUMINUM TRIM, Architectural
To clean aluminum trim use SafeRestore undiluted. Instead of brushing, use a double application without rinsing in between each application. Finish with a pressure wash rinse.
^ TOP

ARTILLERY FUNGUS
Use SafeRestore straight. Spray on two applications without rinsing between applications and finish by rinsing with a hose or pressure washer.

^ TOP

BRICK, New Cleanup
NMD80 is a detergent based solution designed for safe clean up of new masonry structures. The detergent allows fewer applications and can be used comfortably around people. When used as directed, there should be no impact on plants or soils near the site. Recommended dilutions start at 4:1.

For Sand faced brick:Apply the product from the bottom up using either a low-pressure sprayer or a high volume downstream capable of 4:1. Repeat before rinsing with low pressure from the top down to prevent drying.
For S-Type Mortar: Apply NMD 80 using a 3:1 dilution. Repeat application at least twice before rinsing.
^ TOP

BRICK, Restoration
Use SafeRestore or Glazed Surface Restoration. See product instructions.
^ TOP

BLOCK, New, cleanup
Ground face, burnished or any block, including integrally waterproofed colored masonry units, can be cleaned effectively with NMD 80 at a 4:1 dilution. Follow with a pressure washer rinse.
^ TOP

CALCIUM, Hard water stains and copper stains
Use SafeRestore undiluted.
^ TOP

CAULK REMOVAL
Use Graf-Ex. Please call for application procedures.
^ TOP

COATING REMOVAL, from glass
SafeRestore or Graf-Ex will remove coatings on glass.
^ TOP

COATING REMOVAL, when effloresced
Either NMD80 or SafeRestore undiluted will remove effloresced coatings.
^ TOP

COATING REMOVAL, by type
Call for specific guidelines.
^ TOP

Due to the wide variety of coatings currently in use, we recommend a coating removal test kit to determine which product is the best for removing a particular coating. In addition, you may also refer to our website which lists several recommendations for removing more commonly found coatings.

CLAY STAINS, Removal
SafeRestore is recommended for clay stain removal. Low pressure spray on or brush on at 4:1 dilution. Rinse with a pressure washer.
^ TOP

CONCRETE, Removal from equipment and trucks.
Use undiluted Concrete Cleaner, allowing to soak overnight for heavy build up. Rinse with a pressure washer the next day.
^ TOP

CONCRETE, Tilt-up, new
On the job site, NMD80 can be used to clean tilt-up concrete very effectively. The dilution range will vary according to the desired surface finish and should be between 15:1 to 30:1. If the goal is to etch the tilt-up at the plant, a stronger concentration should be used, although the acutal dilution rate will be determined by the desired degree of etch. A high volume downstream nozzle capable of 4:1 may be appropriate for application. Follow with an application of NMD80 which will ensure an even, finished appearance without streaks. Very tall structures should be cleaned one entire section at a time, working from the top down. Additionally,SafeRestore is excellent for removing bond breaker from tilt-up.
^ TOP

CONCRETE, Stain removal
SafeRestore remains the best option for removing metal and mineral oxide stains including rust, lead and copper. For oil stains, use Heavy Duty Degreaser and apply straight with a low pressure sprayer. The stains will also benefit from a brushing after application. This will drive the degreaser deeper into the pores of the concrete and allow it to lift out any shadows. Glazed Surface Restoration (GSR) is the the most economical solution for large concrete structures such as parking garages which may have numerous oil stains. Apply GSR up to 20:1 and finish with a high pressure rinse.
^ TOP

COPPER STAINS
Use SafeRestore undiluted. A copper stain may show up as blue, green or black depending on the elements it reacts with to cause the stain. Generally, an undiluted application repeated twice before rinsing, will remove the stain.
^ TOP

EFFLORESCENCE, Concrete and brick
NMD80 performs well in the removal of efflorescence. Use at 4:1 dilution. Apply with a low pressure applicator.
^ TOP

EFFLORESCENCE, Colored Block
Ef-Fortless will remove efflorescence from colored block and mortar without causing color bleed. For harder calcite-type efflorescence, a pretreatment may be necessary. Spray the product on straight and finish with a pressure wash rinse.
^ TOP

EFFLORESCENCE, Calcite and Lime Putty
Calcite Presoak followed by NMD80 will remove calcite on colored block, brick and stone.
^ TOP

EIFS, Cleaning pollution stains
In one application, SafeRestore easily removes stains caused by hydrocarbons, such as traffic exhaust as well as biological stains like mildew. It contains no bleach. The best application is straight. SafeRestore can be applied with a low pressure sprayer. Use two applications several minutes apart without allowing the product to dry or rinsing between applications. Cleansol at 4:1 to 10:1 dilutions also works very well on EIFS for all but mildew.
^ TOP

GLASS
SafeRestore is great on glass. It will remove atmospheric staining, concrete leachate, silicate soap stains, paint wash stains and many sealers safely, quickly and easily. Generally, one application of undiluted SafeRestore, misted or wiped, then rinsed, will remove these stains.
^ TOP

GRAFFITI, Painted surface
Graf-Ex is a special purpose stripper designed for safety and low odor. It is an outstanding performer in the removal of inks and paints from painted surfaces and works great on adhesives. Water can be used to stop its penetration and to rinse. Graf-Ex is not dilutable. Use it straight and apply with either a low pressure spray or wipe it with a cloth and finish with a rinse.
^ TOP

GRAFFITI, Brick
Stripsol or LCS will remove most tags. Stripsol is a solvent based stripper, good on a wide variety of paints, but safe for the environment. LCS is a water based product also effective on a wide variety of surfaces and paint and should be sprayed or agitated, then pressure washer rinsed.
^ TOP

GRAFFITI, Limestone, block and sandstone
Stripper Cream is recommended for the removal of graffiti on limestone because it will not change the color of the stone or damage its structural quality. Prewet the wall with a pressure washer. The stripper may be rolled or brushed on to help it be pushed into the interstitial pores of the stone. For large areas, spraying would be beneficial.
^ TOP

GRAFFITI, Plexiglass
Spray with Plexiclean, undiluted, then wipe off.
^ TOP

GRANITE
SafeRestore will remove most all stains found on the surface. Undiluted, SafeRestore may be applied with a simple “spray on/spray off” application. Glazed Surface Restoration (GSR) may be applied at dilutions ranging up to 20:1, depending on the type of soil staining. There are no special cautions for SafeRestore or GSR on granite.
^ TOP

GUM SHADOWS, From concrete
Gum shadows can be removed after pretreating the surface with SafeRestore. The best application range is either straight. SafeRestore can be applied with a low pressure applicator and should be left on for 5 to 15 minutes. Finish with high pressure rinse.
^ TOP

GUTTERS
Gutters can be cleaned with Cleansol BC at 4:1, then applied twice, or use SafeRestore undiluted.
^ TOP

LIMESTONE, Indiana and travertine
The most common type of limestone is Indiana limestone that is used to face or trim buildings. SafeRestore is completely safe to use on this stone. If the stone has been well maintained and only mild mildew staining has occured, one application should be sufficient. Prewet the stone then spray on SafeRestore (for deep mildew staining: see Limestone, deep stains.)
^ TOP

LIMESTONE, Black crust
Stripper Cream will remove black crust from limestone efficiently. Prewet the surface and apply undiluted by roller or spray using adequate thickness. The product may be diluted up to 4:1 for mineral stains that are not dimensional. Rinse with a pressure washer, being careful not to harm the surface.
^ TOP

LIMESTONE, Deep stains
For removal of deep mildew stains, a wet on wet double application of SafeRestore may be necessary. Do not rinse in betweenapplications. In extreme cases this may need to be repeated. Finish with a pressure wash rinse.
^ TOP

LIMESTONE, Rust and copper stains
SafeRestore undiluted wet on wet application. Allow it to sit at least 10 minutes and rinse.
^ TOP

MILDEW, from houses, decks, and roofs
Mildew on homes can be treated with a spray on/spray off application of SafeRestore. There is no danger to the home or plants when used as directed. You can expect a longer residual kill than with bleach. On wood, higher dilutions of the product restore the wood to "like new" appearance to the wood without fuzzing or damage.
^ TOP

MARBLE, Unpolished
Use SafeRestore to clean unpolished marble at dilutions from straight to 10:1 and apply with a low pressure sprayer. Rinse with a pressure washer.
^ TOP

MARBLE, Polished
Polished Polished Stone Cleaner Neutral cleans polished marble easily. Apply undiluted product with a low pressure sprayer. Remove with a high pressure rinse or by wiping with a damp cloth.
^ TOP

PAINT, cleaning
Cleansol removes all common stains except mildew without harming the paint. A Cleansol application at 10:1 to 20:1 dilution with a high pressure wash and a high pressure rinse will remove the oxidation and leave a shiny surface. It is very good on gutter stains if used straight.
^ TOP

PAINT, Wash on brick
Glazed Surface Restoration (GSR) or straight SafeRestore will remove paint wash from brick. Apply the GSR straight to 10:1 dilution with a low pressure sprayer. Rinse with a high pressure wash or a garden hose.
^ TOP

PAINT STRIPPING, Multilayer
Stripper Cream is effective for removing multiple layers of paint. It can be sprayed, rolled or brushed with equal ease. The product will not dry out. When applied straight, a skin will form allowing the paint to be scraped off mostly intact or it can be removed with a high pressure wash.
^ TOP

PAINT STRIPPING, Acrylics/Urethanes
Stripsol is used undiluted. Call for application procedures.
^ TOP

PAINT STRIPPING, Latex
LCS or Stripper Cream can be used for stripping latex paint. Apply straight to 5:1. LCS can be sprayed on then rinsed with a pressure wash.
^ TOP

PAINTED STEEL PANELS, Cleaning
Cleansol BC is a concentrated soap that will clean painted steel panels easily. When brushing, apply at 20:1. When using a pressure washer spray downstream with straight product to achieve brushless cleaning results.
^ TOP

PRECAST STONE, New cleanup
See Concrete
^ TOP

RUST STAINS, Concrete
SafeRestore is the first choice to remove stains without bleaching. Glazed Surface Restoration (GSR) will also remove rust stains from concrete. Apply the product at a dilution range of 4:1 to 10:1 with a low pressure sprayer and rinse with a high pressure washer.
^ TOP

RUST STAINS, Limestone and steel
SafeRestore will melt rust stains quickly and help prevent re-oxidation. The best application rate is straight. SafeRestore can be applied with a low pressure applicator. The best use of the product is two applications several minutes apart without allowing the product to dry or rinsing between.
^ TOP

SEALANT STAINS
SafeRestore is an excellent treatment for sealant stains. Apply straight with a low pressure sprayer and follow with a high pressure rinse.
^ TOP

SLATE
To clean normal soil on slate, use Cleansol BC. For more difficult stains such as water hardness and metal or mineral oxides, use SafeRestore. Apply straight with a low pressure sprayer or at dilutions up to 4:1. Rinse with a garden hose or pressure washer.
^ TOP

SMOKE REMOVAL
Smoke melt is a high alkaline cleaning product that will remove heavy carbon deposits from wood or masonry and will soften heavy black smoke from fire damage on masonry. Use at dilutions of 4:1 to 50:1. See label for further application instructions. For interior removal of smoke from stone on fireplace surrounds, SafeRestore is highly effective.
^ TOP

STAINLESS STEEL
HD Sabre cleans stainless steel very well. It also helps prevent future corrosion. Use a low pressure sprayer or downstream at dilutions of 30:1 to 60:1, then use a high pressure rinse. Do not use straight or let dry on the surface. It may be followed by an application of Cleansol diluted 10:1.
^ TOP

TAR REMOVAL
C-Tar Melt will penetrate and soften tar. The product is not dilutable with water. It is safe for wood, metal and masonry surfaces. If a shadow remains in masonry, use Stripper Cream to remove it. In addition, SafeRestore can be used to remove fresh tar stains on brick or block that my have occurred during roof repair. It will also remove shadows as well.
^ TOP

TEFLON PANELS
SafeRestore is excellent for cleaning teflon panels. The best application range is either straight or 4:1. SafeRestore is best applied with a low pressure applicator. Apply two applications several minutes apart without allowing the product to dry or rinsing between each application. Cleansol is an excellent product for maintainance cleaning.
^ TOP

TERRA COTTA
GS Restoration or SafeRestore are both good options for terra cotta restoration. The best application rate is straight. GSR and SafeRestore each can be applied with a low pressure applicator. The best use of the products is two applications several minutes apart without allowing the product to dry or rinsing in between.
^ TOP

VINYL AWNINGS
Cleansol is very effective in the cleaning of vinyl awnings. When brushing, apply straight to 20:1. When using a pressure washer cut product 4:1 to achieve brushless cleaning results.
^ TOP