Sizzle

 


 

Brushless Truck Wash

Description and Use

SIZZLE is brushless pressure wash soap. SIZZLE truckwash system is versatile in the ways it may be applied: lowor high pressure as well as through foaming arch. Highpressure application will give faster performance and higher dilutions. The product works best when heated, also functions well cold. The water softeners are built in and are to be used to the greatest advantage if premixed at high dilutions before application. A pressure rinse is recommended with the SIZZLE.

Advantages
High dilutions

Limitations
Not safe on polished aluminum, passable with a quick rinse

Technical Data
Appearance & Odor: Brown color, mild odor
Physical State: liquid pH: 12.8
Vapor Pressure (mmHg): As water
Vapor Density (air=1): As water
Boiling Point: 210째F Freezing/Melting Point: N.A.
Specific Gravity (water =1): 1.06
Evaporation Rate: As water
Solubility in water: Complete

Preparation

Surface and Air Temperatures
Excessively high or low temperatures will produce poor results and possible harm. Best cleaning results are obtained when air and surface temperatures are 40째 F or above. Do not clean when temperatures are below freezing or will be overnight. If freezing conditions exist, allow adequate time for surface to thaw. If air temperatures exceed 90째 F, flash cool the surface with water before applying product. Do not allow product to dry on a hot surface.

Pre-Testing
Always test prior to beginning full-scale cleaning operations. Testing should confirm cleaning effectiveness on each type of surface and stain designated to be removed. Testing also determines the desired dwell time and any potential for adverse reactions with adjacent materials. Allow test panels to dry thoroughly before evaluating final appearance and results.

Dilutions
- 20:1 low pressure brushless
- 30:1 high pressures brushless
- 100:1 brushing application

Application

General Application
This product may be applied downstream or upstream through a pressure washer. You can use a low pressure applicator or by brushing. Rinsing is best with a pressure washer for brushless clean or with a garden hose after brushing. Do not allow the product to dry on the glass.

Safety Information

Precautionary Measures
Precautionary measures: Always wear goggles and rubber gloves when handling this product. Keep off of skin and clothing. If material comes in contact with clothing, wash before reuse. It is important to wear eye protection at all times when handling this product. Do not get in eyes, on skin or clothing. Keep container closed when not in use. Do not allow product to freeze. Do not remove label. Read Material Safety Data Sheets for additional safety and health hazard information prior to use.

Spill or Leak Procedures
Check with the state, local, or federal regulations for waste disposal methods in the area. Wear proper protective equipment while doing cleanup. For large spills, dike and contain for intended use. For small spills, use a chemical absorbent product and place in approved container for disposal.

Container Handling/Storage
Precautions to be taken in handling and storage: Keep container closed when not in use, store in a cool dry place.
Other Precautions: Store away from acids.

First Aid +

Instructions in Case of Contact or Exposure
Eyes: Flush thoroughly with water for fifteen minutes. If irritation persists, seek medical attention.
Skin: Wash off with soap and water. Moisturize skin. If irritation persists, seek medical attention.
Inhalation: Remove to fresh air.
Ingestion: Do not induce vomiting. Drink large amounts of water. Seek medical attention.

Other

Notice
This product has been classified in accordance with the hazard criteria of the CFR.

Disclaimer
The information herein is given in good faith, but no warranty, either expressed or implied, is made. Final determination of the suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein we cannot be sure or guarantee these are the only hazards, which exist.

Customer Service
Factory personnel are available for assistance at 800-313-8505 and will send you additional information on products as necessary.